The special magnetic auxiliary contact pressure gauge is a pressure gauge with an electric contact device. It is often used together with the corresponding electrical devices to measure non-corrosive copper alloys, no explosion risk, and non-crystalline various liquid and gas media. pressure. The electric contact pressure gauge is used to measure the positive and negative pressures of gases and liquid media that do not cause corrosion to copper and copper alloys. When the pressure reaches a predetermined value, it sends a signal and turns on the control circuit to achieve automatic control. The electrical contact pressure gauge has a dual-position automatic control and signaling alarm function.
Special magnetic auxiliary contact pressure gauge Note 1, the electrical contact pressure gauge should be installed vertically, and strive to maintain the same level with the measurement point.
2. After the electrical circuit of the electrical contact pressure gauge is properly connected, tighten the compression nut and carefully inspect and perform the test operation.
3, electric contact pressure gauge in the measurement of stable pressure, can be used to the upper limit of 3/4; in the measurement of alternating pressure is used to the upper limit of 2/3; measurement of negative pressure is not limited.
4. When opening the outlet box or adjusting the upper and lower limit setting range, you must first cut off the power supply.
5. In the case of normal use, the electrical contact pressure gauge should be inspected periodically and at least once every six months. Electric contact pressure gauges such as sudden problems (pressure loss due to leakage of the spring tube; contact welding, or reliability due to severe oxidation affecting the continuity of the contacts, failure of pointers, etc.) should be immediately Check or replace it.
6. The electric contact pressure gauge should always be kept dry and clean during use.
7. The reliability of the explosion-proof performance of the electrical contact pressure gauge depends mainly on the compressive strength of the flameproof enclosure and the quality of the flameproof enclosure. Therefore, in the process of installation, use and maintenance, be sure to pay attention to the flameproof surface, do not bump scratches, especially when dismantling the junction box of the electrical contact pressure gauge or pay special attention when performing a complete overhaul. No painting is allowed on the flameproof surface.
8. During inspection and maintenance, if the user is not clear about the basic knowledge of explosion-proof electrical equipment, the structural features and requirements of the explosion-proof electrical contact pressure gauges are not well understood, and they must not be pieced together or refitted at will, otherwise they will be damaged. The explosion proof performance of the contact pressure gauge.
Special magnetic auxiliary contact pressure gauge Note 1, the electrical contact pressure gauge should be installed vertically, and strive to maintain the same level with the measurement point.
2. After the electrical circuit of the electrical contact pressure gauge is properly connected, tighten the compression nut and carefully inspect and perform the test operation.
3, electric contact pressure gauge in the measurement of stable pressure, can be used to the upper limit of 3/4; in the measurement of alternating pressure is used to the upper limit of 2/3; measurement of negative pressure is not limited.
4. When opening the outlet box or adjusting the upper and lower limit setting range, you must first cut off the power supply.
5. In the case of normal use, the electrical contact pressure gauge should be inspected periodically and at least once every six months. Electric contact pressure gauges such as sudden problems (pressure loss due to leakage of the spring tube; contact welding, or reliability due to severe oxidation affecting the continuity of the contacts, failure of pointers, etc.) should be immediately Check or replace it.
6. The electric contact pressure gauge should always be kept dry and clean during use.
7. The reliability of the explosion-proof performance of the electrical contact pressure gauge depends mainly on the compressive strength of the flameproof enclosure and the quality of the flameproof enclosure. Therefore, in the process of installation, use and maintenance, be sure to pay attention to the flameproof surface, do not bump scratches, especially when dismantling the junction box of the electrical contact pressure gauge or pay special attention when performing a complete overhaul. No painting is allowed on the flameproof surface.
8. During inspection and maintenance, if the user is not clear about the basic knowledge of explosion-proof electrical equipment, the structural features and requirements of the explosion-proof electrical contact pressure gauges are not well understood, and they must not be pieced together or refitted at will, otherwise they will be damaged. The explosion proof performance of the contact pressure gauge.
* Fits all standard oxygen sensors with M18 x 1.5 O2 sensor adapter.
* Straight bolt-on, no modification needed, quick and easy installation to remove check engine light.
* High Quality Material-Made of Stainless steel which can avoid cracking and excessive heat expansion,
* Backed by 1 year warranty and our 100% satisfaction guarantee
* Built in micro catalytic converter, eliminate checking engine light(CEL) after modifing exhaustor or removing catalytic converter. The cell size of the cell 400. Euro 3.
Product Description:
*Solve the problem of P0420/P0042 codes faulty.
*Faulty catalytic converter is the most common reason to cause fault codes P0420/P0042. Include:
1. Check Engine Light is on.
2. Lack of power after vehicle warms up.
3. Speed of vehicle may not exceed 30-40 mph.
4. Rotten egg smell coming from the exhaust pipe.
2. Lack of power after vehicle warms up.
3. Speed of vehicle may not exceed 30-40 mph.
4. Rotten egg smell coming from the exhaust pipe.
* Install our Oxygen Sensor adapter which includes mini converter could help solve the problem.
Oxygen Sensor Spacer,O2 Sensor Spacer,Mini Catalytic Sensor Spacer,180 Degree Oxygen Sensor Spacer
Dongguan Jiaxing Precision Machinery Co., Ltd. , https://www.jiaxingmachinery.com